I seriously like this tablet mount. The only reason i am supplying it four stars is simply because of the plastic ring, which is the weakest component of the total point. Total, which is a single of the most effective tablet holders for mavic, which is a) seems realy nice b) is pretty nicely created (apart from for the plastic ring) and c) is very relaxed to use. I am never concerned that my tablet will tumble, i can keep it devoid of difficulty and the bodyweight doesn’t give me any problems. I also want to mention, that the customer service is very great. I have contacted the corporation declaring that the ring was damaged and they despatched me a substitute with out any inquiries, mentioning that a new product will soon hit the marketplace, where the plastic ring challenge is set.
The item does exactly what it claims to do, nonetheless the make good quality of some of the sections is missing. Precisely, there is a plastic nut that you tighten to keep the tablet in area, even so the plastic is poor high-quality and broke with standard use in just the very first handful of months of ownership. This failure qualified prospects the tablet to spin close to and not be secured correctly. I have absent to my local components store to buy a alternative nut, however they do not show up to have something that will suit. If the plastic areas of this merchandise were being redone in metallic or far better excellent plastic, this would be a five star merchandise. As it is, due to the fact it is not resilient and the failure observed earlier mentioned results in the merchandise to not perform for its meant functionality, it is a three star merchandise.
I’ve been employing for a very little while and totally like the concept. Only down drop is the screw and the female threads are produced of plastic. I cannot in excess of tighten really hard or it will strip. I am remaining to maintain my ipad any way. Wish the screw and felmale adapter was aluminum like metallic. It would continue to keep fat down and make the integrity more powerful.
Finest attribute: it can be compact and easy to store/transport. I use it with an ipad mini 4 in an otterbox defender scenario. It retains the ipad organization and is well balanced. I also bought the rcstyle lightning usb cable and the pgytech l168 monitor hood. It really is the great set up, all-close to, imho. And if you dress in a black tee shirt, the glare is lessened about as significantly as you can request, quick of shady tree or a crystalsky check. (the case is a nanuk 920 and the skin is photo voltaic storm from decalgirl.
This product functions great it is definitely nicely built and holds a nine. There ended up no guidelines in the box but its effortless to figure out. Connect the base plate exactly where you would place your telephone. Recall to eliminate the quick cable from the controller very first, (keeps from damaging cable), and acquire the controller knobs out in advance of attaching plate. When not installed it collapses to a practical size. I definitely like this product and would remarkably endorse to any individual who wants to use an ipad fairly than a little monitor smartphone.
I enjoy this as it is like legislation enforcement variety strong lol. The plate thingy you put into the controller jaws or grip thingies lol, is all plate sort metal and the full thing is seriously sturdy and tremendous interesting. Was difficult acquiring my ten inch huawei media pad into it simply because i was striving not to brake it right before i knew how resilient it is. Now that i have, it really is tremendous strong and would in good shape a 12 inch tab for positive. It does transfer all-around a bit but i am confident which is mainly because my tab weighs like a rock lol but indeed i suggest to anybody and everyone super pleasant get, i will unquestionably get my buddy one particular who has a tablet but doenlsnt use it b induce he won’t have 1 of these.
Its what i was glimpse for and operates completely for a tablet (i use a ipad). Do be expecting your controller to be top large when working with a much larger tablet but that to be predicted. With the correct placement you will not really discover it. Its nice to be able to see a dwell check out of the digicam on a larger monitor lets you get better pictures/video. The tablet set up functions much better if the tablet can receive cell signals for gps destinations which is an included value (not demanded how at any time it is substantially nicer). If your on the lookout at some thing such as this i say get it, its low cost and awesome.
Key specs for Skyreat Mavic Air Pro Foldable Aluminum-Alloy 4-12″ Ipad Tablet Mount Holder for DJI Mavic 2 Pro, Mavic 2 Zoom/Mavic Pro/Mavic Air, DJI Spark Accessories Remote Controller:
- Make sure this fits
by entering your model number.
- Aviation aluminum-alloy material made, CNC technology, High quality design accessories Perfect fit with DJI Mavic 2 Pro/ Mavic 2 zoom/ Mavic Air/ Mavic Pro/ Platinum/ DJI Spark remote controller.
- 120Mm-190mm wide support 4-12 inch phone & tablet, 45 degrees to up and down support a clean view, tighten & stable, will stay in the place you need.
- Foldable and iPhone sized.Light weight, only about 227G, convenience to carry outside with other Mavic accessories together.
- Just need 2 step to snap on/ off with no tools.
- Support tablet sunshade & Hanging lanyard.
Comments from buyers
“This is your mount! No need to spend $$$ on fancy alternative. Works FANTASTIC! Very pleased., Well made product, one weakness., Perfect With ONE Issue”
This cell phone/tablet holder does an outstanding career of holding much larger measurement telephones, in my scenario the notice 8. It is properly designed and imagined out. It features a bigger dimensions hole to join your telephone/tablet by one of the supporting sides, one thing the opponents do not involve. It folds up to a little sizing, and fits properly in my drone bag. For comparison, the longest portion of this is about as extended as the controller alone, and fifty percent as thick.
I am amazed by each the functionality of this tablet mount and how perfectly created it is. Dji’s products screams excellent and this solution by skyreat does the similar. It is precision built and suits seamlessly to my mavic air’s remote. It breaks down into just two principal parts which match quickly into the case that came with the mavic air’s fly extra package deal. I am making use of mine with a samsung 9. I also examined it with a observe five mobile cellphone, and each suits perfectly from a ergonomic standpoint. I really would desire this mount for my take note five. It breakdowns/sets up easily and speedily. You will not be dissapointed.
I am not sure what i was expecting but this thing is well built. I have not even installed it in my controller yet and i am sure that it will work perfectly with my 8 inch samsung tablet. The clamp for the device (tablet) is strong and holds well. The only potential weak point is the gimble which is made of molded plastic (pictured) but i suspect with proper use and care it will not be a problem. I’ll write more after i have used it a bit. Works as a great desk stand for your tablet as well.
It significantly enhanced the fun of flying my drone for the reason that i now get to use my greater samsung galaxy tab for the monitor. When traveling right before i made use of my google pixel cellphone. I would have to consider the include off, run the usb cable through the gap, and than jam my cellular phone in the holder. The design on this gadget is excellent. Strong metallic foundation with a hard plastic holder. The spring that retains the tablet in location is strong, not heading to dress in out whenever before long. Genuinely secures my tablet well. I really like that the display is on a ball joint so i can go it all-around to get a greater angle on the screen. Loads of space for the controls.
I like it because you can fold it to retail outlet it in a bag. It will come with its very own storage bag. I desire it was manufactured of plastic because the body alone is metallic that it can mar the rc’s plastic. It matches ipad mini 4 with otterbox situation extremely well horizontally. I mount it differently as demonstrated in the advert. I have the stalk to the pilot and i have excellent see of the rc display screen and the ipad. I desire it was manufactured of plastic but i guess it is tricky to sustain sturdy folding system.
This is a must have if you plan to use a tablet to fly your mavic or spark. This solution is manufactured seriously well, arrives apart simply and folds (almost) flat for uncomplicated storage. I use it with the scaled-down ipad pro and it suits in the holder pretty snugly. I have by no means had any issues whatsoever with my ipad keeping in place or moving when applying it. The mavic controller with this holder, the ipad pro and big solar shade is very manageable from a with standpoint, and even even though it has a gap to attach a lanyard, i simply cannot see anybody truly needing to do that mainly because of fat. I have found some issues about he plastic tensioning knob, but i can notify you it will not be a problem, all the areas and items appear to be to be produced very properly.
Only damaging is you can not see the display on your controller when using this in its recommended posture. Many others complain they broke the plastic nut, and i see they’ve now upgraded it to a steel a person. If i purchased a single all over again i’d go metal, but occur on people, you never have to tighten it down that difficult. In any case, will make a great ipad stand even when not using it to fly. I also use this to prop up my ipad when observing flicks or making use of it with a keyboard. Superior solution and would get all over again.
Good product but description could be a great deal clearer. Does not match a tablet that is eight-one/2” extensive. It claims tablets involving 4” and 12”, but does not specify that it suggests diagonal screen dimensions. If i had transformed the metric measurements, i would have realized that the enlargement of the bracket only goes to about 7-one/2”. The merchandise looks well produced even though i will have to return it.
I had an additional firms variation of this before this yr. Was produced of plastic and didn’t consider extended prior to it was not performing any more. Metal, sturdy and it folds up to a pleasant minimal bundle that can be stored in a thin sleeve and put into a backpack or situation. I desire i experienced this months back.
I have an otterbox defender on my telephone and was acquiring fatigued of using it off each time i wanted to fly. The mount makes it possible for me to use the larger sized display of an ipad while holding it tremendous secure. It packs absent properly and feels like terrific high quality (minus the plastic nut). I have just been light tightening the nut, but i can see wherever it may possibly fail eventually. I may perhaps up grade by having a vacation to the components retail outlet at some place, but it definitely retains high-quality if you never crank it down way too tight.
So significantly no difficulties with this, i appreciate it due to the fact i do not have to eliminate my apple iphone protect in order to squeeze it into the handgrips of the mavic pro controller, lining up the iphone connection. It feels perfectly made, not affordable plastic by any means. It does give some extra body weight to the rc, that could be a downfall. I considered a lanyard arrived with this, which would enable immensely. Right after seeking at the solution once again i guess it does not.
I like the reality that it is built of aluminum. Operates definitely effectively and it has a compact layout for storage. I know somebody broke the significant plastic nut but you only want to tighten it just more than enough maintain the tablet from going. The only difficulty i have experienced so much, immediately after six months of use, is the folding arm attachment points will not continue to be restricted. The screws remain tight but i believe it is a don position problem. I can set some blue loctite on the screw or i have even wrapped some copper wire about the screw prior to i mount the arm. It all is effective great for awhile but finally, after folding and extending the arms a few dozen moments, it loosens all over again. I would like to try a smaller plastic washer but it’s complicated to discover 1 that little. If i can figure out a prolonged-phrase resolve for this problem i would gladly give it 5 stars.
I have been applying this holder with an ipad mini 4 for a little bit less than two months. In general i’m amazed with the top quality of the construction and products utilized, except the plastic nut applied to tighten the ball swivel. It labored great appropriate up right until yesterday, when mid flight the plastic nut split, leaving me with an ipad flopping close to. To be fair, i could have been overzealous tightening the ball joint. Skyreat was contacted, and graciously available to mail a new nut. While i am absolutely sure that the plastic nut is ample, a person manufactured of aluminum would be much much more long lasting, and match the relaxation of the holders higher high quality development. Use warning tightening the current plastic nut and you will probably be high-quality.
Execs: works excellent, holds the tablet around my remote and allows me to alter the tablet for glare or usually and retains it in put. It took me a minute but i was able to get it all figured out without the need of admitting defeat and on the lookout at the guidelines so it is uncomplicated to setup and use. The style is smart and folds up in the furnished felt bag nice n small. The bracket that holds the tablet is stout and spring loaded with an motion that feels sturdy adequate. The foundation of it that attaches to the remote is a good piece of steel with very good heft so you can shut the remote arms on it and keep on as tight as you like. Downsides: the base of the holder arms slips into a ring and a threaded collar is screwed down about it to maintain the entire upper element in area. Now this will work out of the box. But the plastic of the round bits on the arms, and notably the component they slide into are very slim and it looks like they will require to be addressed gently. The unit operates, so 4 stars it is, but i would be happier paying out a few pounds more for anything a little bit beefier to keep up my tablet. Summary: this detail is worthy of the price tag but if you are the kind of kid that, against all statistical likelihood, normally ends up with the toys that split truly early on, i recommend wanting somewhere else.
Bought this to use with my dji spark and it functions good. I’m new to drones and noticed so many alternatives out there it was perplexing. Was contemplating a common mount that charges three-four occasions as a great deal as this just one. I’m sure there are some slight positive aspects to the far more expensive different. The foundation on this product does have a incredibly slight wiggle exactly where it joins the remote, but not problematic in any way. This a single is not as very, but it is also significantly fewer pricey. I have been definitely happy with this mount and am happy i selected it. I’ve been working with it with an ipad pro nine. 7” and it’s so a lot nicer than applying it with the apple iphone. I also purchased an otg cable to direct join the ipad to the remote, which i like as nicely.
What a variance this will make over working with my iphone. At the time i started using my ipad, it was so substantially easier to control the drone. The product or service is extremely effectively created, major duty, and intelligent engineering. At very first, i couldn’t figure out how to get the stand to go up so i could mount the ipad cradle. For the reason that there was no ‘ball’ joint apparent, it seemed unachievable. Last but not least when i figured out that the holes in the bottom of the mounting plate ended up to push up the 2 items of mounting bracket, wallah, the balljoint appeared when the items of the bracket came jointly. Vefery intelligent way to conserve house in folding it away and storing it in the minor travel bag that arrives with it. I hang it on my spark combo bag with a small clamp. This is a well produced item that functions.
I really don’t use this one hundred% but which is not simply because of the item. When i want to do rapid flights, i normally just cram my ipad mini into the typical mavic holder slots. But, when i want to burn off a couple batteries or i am working with it, i use this for numerous explanations. (1) it raises the ipad up so i can attach a hood, (2) it gives me a area to connect a lanyard, and (3) it would make it look much more experienced in scenario a client is looking at (fewer toy like).
I lower a notch in upright and removed the middle put up out of the moveable stop on the bracket. This authorized me to run the cable from the center usb port on the controller to my apple iphone seven plus while the cellular phone is in my otterbox circumstance. I like the point that i no more time have to take out the cell phone from its protective situation to use it to fly. Suppliers could improve these holders by extending the arms on the close a minor better to accommodate protective cases. This is the finest of the brackets on the marketplace for my cash. It is produced of aluminum and transports in a really compact form. The middle gap in the plate is effective fantastic for my lanyard. Now if i just had a shade that would in good shape the otterbox case i’d be in terrific shape.
I bought my cracked-glass ipad mini fixed to use with this. Great applicationat to start with i imagined this was component of a procedure, and that i was missing a aspect. Then i figured out the two arms with semi-spheres at the ends folded collectively and suit into the locking ring. I like the durable steel plate which matches snugly into the phone grips of the controller handles. The tablet clamping procedure is very organization i experienced no dread of the tablet slipping out. I clipped a lanyard into the hole of the plate to offer stability. I also snaked a l-shaped micro usb/lightning cable by way of the holes where the semi-spheres nestle when not in use. This retained the cable out of the way. Of all the (countless) accessories i’ve obtained for my mavic pro, i like the high quality, layout and software impression the most with this skytreat tablet holder.
Immediately after accomplishing substantial investigation on the numerous manufacturers marketing these goods, i at last came to the selection that this 1 seemed the best — and boy was i correct. It’s durable, low-priced, looks sharp, and holds my ipad with no me owning to worry. Additionally, the design at the rear of it is practically nothing small of genius. I adore how it folds up and stores quickly in the circumstance. Who is familiar with how it will hold up above time, but as of now it deserves five-stars for absence of any complaints on my close.
This will work nicely for its intended reason of holding a tablet. My original smaller sized 8′ tablet did not healthy limited more than enough and i had to incorporate two tiny foam inserts (not incorporated) to the ‘jaws’ to make it safe. My newer bigger 10′ tablet fits incredibly well. It’s possible its a nitpic, but it came in a flimsy box with no pics or directions, not that it seriously wanted them, but continue to.
This adapter suits terrific with my nine. I find if i insert the holder into the mavic pro upside down then i’m also nevertheless able to see the controller display which helps. The only draw back i see is the nut that keep the bracket alongside one another is plastic and i fret more than time that may possibly not hold up the finest. I have been utilizing it a number of months with no any challenges.
So much, i’ve flown my new mavic pro2 zoom with the skyreat for about twenty several hours. This is an excellent addition to my flight kit. I normally like to use the more substantial screen of my ipad for the potential to body and target pictures, as well as see all of the mavic readouts all around the image. Holding the ipad can be a obstacle. I have this married with a nice hood, and a 1ft. Cable with a suitable angle on the lightning finish of the connector. I very suggest the appropriate angle plug with this set up. If not, with a straight plug, your still left hand will strike the cable and it is in the way going back again down into the skyreat. I see what other reporters have pointed out about the possibility of the huge nylon nut that secures the spring loaded holder to the mount failing. I located a steel model of the similar nut at a local components keep and it is big.
Tablet holder is strong, sturdy and so slim and artfully well-designed. It sits in front of the controller, but you can look over the top. Mostly you’re just using the thumb controls and not looking at the controller screen since much of the information is on the tablet in front of you. You can flip the tablet pinching part around to move the tablet slightly further below the upper end of the controller in your line of sight. It is so simply built that i thought parts were missing to start with. The flat piece of strong aluminum has two flat arms that fold out words to form the bond that the tablet holder snaps onto then one plastic nut tightens up. If you do not over tighten the nut you should be fine. Possibly a metal nut would do better but i’ve had no problems.
The connector is spring loaded giving overall flexibility to fit almost any size monitor. I use an ipad routinely to have further viewing area for getting comprehensive movies. The bracket matches securely in the remote handle and feels powerful. The metal foundation provides appropriate pounds to the remote to stability out a larger sized ipad display and manage a cozy centre of gravity. You can not see the controls when using a big monitor but it should not be an difficulty for an expert pilot. General it is a fantastic addition to my mavic air.
This all-aluminum (other than the locking nut) is very steady, has an ingenious design the place the arm folds flat into the foundation plate, and enables use of a total-size ipad air. The device when assembled and loaded is quite well balanced and stable, but the just one draw back is that the view of the controller exhibit is fully blocked. Because i largely emphasis on the ipad, this is not a deal breaker, but i do want they would have figured out a way to keep viewing of the exhibit. The only other downside is that due to the reliable aluminum development, this one’s a bit on the hefty facet for vacation.
The base and cellular phone holder comes apart and folds flat fitting into a little felt like carry bag (bundled) together with a substantial good quality usblightning cable (not integrated). Employing this my cellular phone (an apple iphone eight furthermore) can be still left in the cell phone case, the cellular phone display is not blocked by my palms sitting on the controls, the software in the phone does not drop the connection to the remote (which often transpires with the dji usblightning cable. This is a should-have for a person with a mavic (mine is the first mavic pro). I can see exactly where the plastic nut could cause troubles but for me that would not appear to be to be an difficulty (i don’t really feel the require to tighten it down pretty significantly and my mobile phone however feels locked limited and i completely get rid of the nut in advance of removing the holder (so that you will find no additional stress on the nut as the foundation is slid out).