Akk is my go to vtx for all my quads. . Works better and more durable then the top brands.
Really like this, have it hooked up via intelligent audio and will in no way go back to a regular vtx. Photos clean up and no issues.
Ok if you want a stackable but otherwise too big. Never could get smart audio working.
Just make certain you mount on top of stack if triple stacking your boards. They deliver some warmth on greater wattage’s. On the other hand i have a handful of of these and they operate great.
Straightforward put in, clever audio labored effectively, mmcx is usually a reward. Failed to keep up perfectly contemplating dimension and form component. With no severe crashes lasted only a handful of months at ordinary mw concentrations.
Has all the preferred functions minus the delicate start off up. So you will interrupt other ppls feed when powering on. Other than that very good video energy and a really sturdy board. I haven’t located anything at all much better for much less money. I have two and each operate good. Burnt my unify out (finally. By considerably the very best vtx i’ve applied to date) and was looking for a cheaply to get me back again in the sky, so contented i purchased a next. Would deff propose to anyone on a spending budget ).
My New Go To VTX. Buy this!
Great vtx for the price
Love How this VTX mounts in the Stack and Has a MMCX Antenna Connector
Almost everything about this transmitter is wonderful. Switchable electrical power levels with smart audio control. Matches completely beneath or around the fc. It supplies a thoroughly clean 5v out for the digicam. Paired up with a reduced esr cap on the battery lead results in virtually noiseless video clip. The pigtail connector is good due to the fact it is rated at in excess of a hundred link/disconnection cycles. I would endorse this to a buddy, for sure.
Dependent on your setup you may well want a more time mmcx to sma cable. Just took it for a spin and had no video clip concerns in anyway. I love that it has wise audio so i can transform the channels from my taranis or my osd in the goggles. I see no reason to spend much more funds for any other vtx.
Terrific merchandise awful packaging. Came with further mmx connectors and 1 was tremendous bent. Bad packaging just about no cushioning. Hope the vtx lasts following dealing with the mail.
My new go-to vtxordered two as i have quickly developed to like akk’s a5 for my small whoop’s and experienced to give this a shot as it checks off quite considerably just about every box i have for want’s or wants in a vtx. Easy to go through led, and simple one button navigation. Sensible audio to make variations via my osd, wonderful. 800mw of power if needed, double wonderful. Not that i use it but i could and solutions are what i’m afterthe only alter i would make is to have the mmcx pigtail be the conventional rp-sma (feminine) so i didn’t have to use an adapter. Normally, this detail is fantastic, and the mmcx is a welcome change.
It is effective great and is created nicely. Really like the numerical show (blue figures) in its place of counting led blinks.
Features of AKK FX2 5.8Ghz FPV Transmitter 25mW/200mW/500mW/800mW VTX with MMCX Support OSD Configuring via Betaflight Flight Control Board
- Make sure this fits
by entering your model number.
- 25mW/200mW/500mW/800mW power switchable
- Support OSD Configuring via Betaflight Flight Control Board.
- 7-24V input and can be provides 5V output for your camera,can use standard voltage 6S battery input, can not use high voltage 6s battery input Standard voltage: 3.7v x 6s=22.2V, high voltage: 4.3v x 6s = 25.8v
- Filtered power ensure super clean video, born for racing. One button frequency and power setup.
- 0.01mW power with zero interference,Compatible with Betaflight OSD FC
Make sure this fits
by entering your model number.
I have damaged 2 of them in some really large crashes, but currently was the initially day it shorted out on me. Not really certain why lasted me three months kinda disappointing.
Seems to get the job done really nicely so considerably. Vary could be a very little greater i assume but for the price tag not too poor.
Appears to perform fantastic so far, time will notify. Seeking ahead to reviewing extra akk merchandise.
Can change channel via osd, has the mic built in, mmcx for security.
I however have to construct out a quad with this vtx but have no doubt that my prepare for the construct will do the job out great with this vtx. The 30mx30m mounting choice is best with a tpu antenna mount off the again 2 stanchions.
Comparable to tbs unify, except less complicated to use and far better antenna mmcx plug.
25mW/200mW/500mW/800mW power switchable
Only factor is i crashed and the led indicator fell off but vtx nonetheless will work i just cant change electricity configurations because i cant see the indicator led.
Lasted me about six months, toasted just after a spirited conference with a brick wall. The tiny on board display screen nonetheless works but no video to my headset.
Great if you get it working the first time, i had to replace it, because the first one, as soon as i conected it, it blew smoke. , the second one is working great.
I’m giving this vtx 5 stars even while it will not have a sma selection. I just ordered some rp-sma antennas, but my other twenty miniquads are all sma, which is possibly ninety% of the miniquad marketplace. I would like to see this vtx without the mmcx connector(does any one have to have it?) and just solder a sma pigtail to it. Significantly less signal reduction without the fancy connector(guessing). ninety nine and akk technologies would likely make more income. I feel those people mmcx cables aren’t low cost. Video clip top quality is prime notch, no horizontal strains in the video. Array appeared rather excellent, but i am testing with an aged, old, outdated clover leaf antenna from banggood, only rp-sma antenna i have. If you can live with the rp-sma link, then this is a excellent offer. I am heading to do a online video assessment of it on youtube, research for mooosestang with three o’s. Also the base of the board has no factors, so you can mount it quite shut to your flight controller, which was pleasant in my circumstance.
Hooked it up today and smart audio works perfect on cl racing f4 aio betaflight 3. 4 stars for now due to the mw reading is slightly below on 25 mw. It reads about 18 mw on direct plug in but checking with the sniffer it is right on the money. I’ll come back and 5 star if it doesn’t give issues racing on 25 mw. I use all akk vtx but this is my first smart audio vtx.
Even if you aren’t having all the output electric power advertised this is even now a nicely-created wise audio capable and stack-able vtx for fifty percent what the superior conclude manufactures demand. A single other gripe is the pig-tale, it wants to be ninety degrees at the board.
Support OSD Configuring via Betaflight Flight Control Board.
Merchandise came in and it was a return. I obtained a made use of vtx witj broken antenna and sticker label taken off. Didnt even arrive with harness. So they need to have discovered. Now i can not fly this weekend.
What i like most is how quickly it integrates into my flight stack.
For an economical fpv transmitter, this is a definitely fantastic decide. I have had it for about 6 months and it is nevertheless likely strong. There are almost certainly greater good quality fpv transmitters out there, but absolutely not at this rate issue. Pro’s – minimal profile and effortless to mount to your flight control stack – selectable wattage from 25 mw up to 800 mw – comes with all cables necessary to get you in the air – tiny screen presents channel information (considerably much easier than counting led blinks)con’s – gets a small sizzling at the larger wattage levelsoverall, a terrific transmitter for a incredibly inexpensive selling price. Will certainly buy yet again for other fpv builds.
Smartaudio port works flawlessly. Channels are pretty well centered in their frequencies, minimal bleeding at 25mw and 200mw. Applied silicone conformal coating with no problems.
Was quite quick to install and set up. I was drained of breaking my vtx’s so hoping this will last significantly for a longer time, so considerably so good.
Ive acquired three of these i like this vtx so considerably. I place it on the best of my alien stack and operate the mmcx connector to the back. It is practical to be able to disconnect with the mmcx connector when your connected to the prime-plate. But the my beloved function is the onboard mic. It sends audio to my fatsharks on the remaining channel. Fatsharks pickup on the remaining and i have a mono ear pod that is wired for the still left channel. This all is effective with each other flawlessly to give me the great audio quantity degree with out possessing to mess all around with volume on my fatsharks.
I certainly really like this matter ,for a discount vtx don’t believe this can be beat. My movie feed has been tremendous good ,the cause for the 4 stars and not 5 is the rpsma. I’ve had to run an adapter ,all my antennas are sma.
7-24V input and can be provides 5V output for your camera,can use standard voltage 6S battery input, can not use high voltage 6s battery input Standard voltage: 3.7v x 6s=22.2V, high voltage: 4.3v x 6s = 25.8v
I replaced the stock vtx on my wizard x220 with it. I really like how it mounts in the stack. No much more zip tying the vtx somewhere on the frame. Switching the configurations with the button is easy too. The sign is sturdy and crystal clear. I have viewed some lines when i punch the throttle, but it is nothing at all far too negative. I actually really don’t even see it when i’m flying. Also, i am a massive lover of the mmcx connector for the antenna. A great deal greater than the tiny jst sort connectors. I had difficulty with the old connector wiggling loose causing me to reduce the fpv signal mid-flight which is not superior. This vtx fastened that challenge. For the dollars, this is a good vtx that i’d obtain once more.
Is effective wonderful and appreciate that it has smart audio. The mmcx connector is effective effectively. Only factor that would make it improved is if it experienced solder pads rather of the connector to attach the cables to the flight controller.